About | Linear Motion Components | Support Components | Fasteners | Bearings | Rollers | Sheet/Rod | Pulleys, Sprockets, Wheels | Chain Tensioners | Product Worksheets

POBCO Screw Conveyor Flight Edging

POBCO Ultra-D Flight Edging is used to snap-on over the screw conveyor flight to extend the life of the flight and to allow for improved clean-out of the trough. It is normally installed by winding it along the screw so that it snaps on in the well between the flights and secured with metal rivets. Starting at one end the UHMW plastic is tapped into place by moving along the length of the screw. This Ultra-D plastic is stabilized against ultra-violet light radiation. The center bearing on short conveyors can sometimes be eliminated when the center of the screw sits lightly in the trough.

  • UV Stabilized For Outdoor Use
  • Improve Clean-Out Of Troughs
  • Eliminate Hangers On Shorter Runs
  • Use With Helicoid Or Sectional Flights
  • Reduce Noise And Wear On Rubbing Screws
50 ft. Standard Coil Lengths.
Many Sizes In Stock.

Screw Conveyor Flight Pitch

To determine approximate amount of edging
required in feet when:

Full Pitch = length of conveyor section in feet x 3.4
Half Pitch = length of conveyor section in feet x 6.7
Irregular Pitch = no. of pitches x Dia. (in inches) x .262

Screw Conveyor Flight Edging

 

Screw Conveyor Flight Edging

ULTRA-D
Part No.
"A"
Dia. of
Screw
"F"
Flight
Thickness
"W"
Width
Across Top
"T"
Thickness
of Wear Top
"H"
Height
PFE4-6-063 6" 1/16" .440" .350" .750"
PFE4-6-104 6" 3/32" &.104" .440" .340" .870"
PFE4-6-134 6" 1/8" & .134" .440" .350" .750"
PFE6-6-188 6" 3/16" .630" .350" .750"
PFE6-6-250 6" 7/32” & 1/4” .650" .350" .750"
PFE7-6-375 6" 3/8" .630 .350 .750
PFE4-93/8-.09.15 9" to 9-3/8" 3/32" & .104" .440" .150" .800"
PFE4-9-.09.25L 9" 3/32" & .104" .430" .250" .770"
PFE4-9-104 9" 3/32" .440" .340" .870"
PFE4-9-134 9" 1/8" & .134" .440" .350" .750"
PFE6-9-188 9" 3/16" .630" .350" .750"
PFE6-9-250 9" 7/32" & 1/4" .630" .350" .750"
PFE7-9-375 9" 3/8" .630" .350" .750"
PFE4-12-.09.25L 12" 3/32" & .104" .440" .245" .775"
PFE4-12-104 12" 3/32" .440" .340" .870"
PFE4-12-134 12" 1/8" & .134" .440" .350" .750"
PFE6-12-188 12" 3/16" .630" .350" .750"
PFE6-12-250 12" 1/4" .630" .350" .750"
PFE7-12-375 12" 3/8" .630" .350" .750"
PFE4-16-134 16" 1/8" & .134" .440" .350" .750"
PFE6-16-188 16" 3/16" .630" .350" .750"
PFE6-16-250 16" 7/32" & 1/4" .630" .350" .750"
PFE7-16-375 16" 3/8" .630" .350" .750"
PFE6-18-188 18" 3/16" .630" .350" .750"
PFE6-18-250 18" 7/32" & 1/4" .630" .350" .750"
PFE7-18-375 18" 3/8" .630" .350" .750"
PFE6-20-188 20" 3/16" .630 .350 .750
PFE6-20-250 20" 7/32" & 1/4" .630" .350" .750"
PFE7-20-375 20" 3/8" .630" .350" .750"
PFE6-24-188 24" 3/16" .630 .350 .750
PFE6-24-250 24" 7/32" & 1/4" .630" .350" .750"
PFE7-24-375 24" 3/8" .630" .350" .750"
PFE6-30-188 30" 3/16" .630 .350 .750
PFE6-30-250 30" 7/32" & 1/4" .630" .350" .750"
PFE7-30-375 30" 3/8" .630" .350" .750"